Produktai skirti kompiuterinė atmintis (127)

The AX88178 USB to 10/100/1000 Gigabit Ethernet/HomePNA/HomePlug controller is a high performance and highly integrated ASIC with embedded 40KB SRAM for packet buffering. It enables low cost and affordable Gigabit Ethernet network connection to desktop, notebook PC, and embedded system using popular USB ports. It has an USB interface to communicate with USB host controller and is compliant with USB specification V1.0, V1.1 and V2.0. It implements 10/100/1000Mbps Ethernet LAN function based on IEEE802.3, IEEE802.3u, IEEE802.3ab standards or HomePNA standard. It supports mediaindependent interface (MII) to simplify the design on implementing Fast Ethernet and HomePNA functions. It also provides gigabit mediaindependent (GMII) and reduced gigabit mediaindependent (RGMII) interface for interfacing with Gigabit Ethernet PHY. Single chip USB to 10/100/1000 Gigabit Ethernet and HomePNA and HomePlug Network Controller

MCS9922 is a single lane multifunction PCI express to I/O controller. It supports two serial ports and eight GPIO's. MCS9922 also provides an option for peripheral expansion through proprietary Cascade interface. The generic cascade interface allows interconnecting with similar chips like MCS9900 to expand the peripheral ports. The serial ports are compatible with RS232, RS422 & RS485 standards and supports throughput from 50bps to 16Mbps. All the GPIO pins are programmable and can be used as Input or Output. An I²C interface is provided to configure MCS9922 device options through an external EEPROM. PCI Express Singlelane (X1) PCI Express Endpoint Controller with integrated PHY Compliant with PCI Express Base Specification, Revision 1.1 Compliant with PCI Express card specifications

Couverture mondiale LTE Cat4 UMTS/HSPA+ GSM/GPRS/EDGE GNSS Le Quectel EG25-G est un module catégorie 4 optimisé pour les applications M2M et IoT. Supportant la Rel.11 LTE du 3GPP, le module offre un débit descendant de 150Mbit/s et un lien montant de 50Mbit/s. LTE category 4 module optimized for M2M and IoT applications Worldwide LTE, UMTS/HSPA+ and GSM/GPRS/EDGE coverage Multi-constellation GNSS receiver available for applications requiring fast and accurate fixes in any environment Feature refinements: supports DFOTA*, eCall and DTMF MIMO technology meets demands for data rate and link reliability in modem wireless communication systems Couverture mondiale: EG25-G* LTE FDD: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19/B20/B26/B28 TDD:B38/B39/B40/B41 WCDMA: B1/B2/B4/B5/B8/B6/B19 GSM: B2/B3/B5/B8 Feature refinements: supports DFOTA*, eCall and DTMF

EP124 is a super high speed 10bit LVDS 2port to 4port bridge. The chip converts 2port LVDS input to 4port LVDS output at a pixel rate of 330 MHz. The chip is capable of receiving dualport 10bit LVDS input at 165 MHz clock rate per port and convert it to 4port 10bit LVDS output at half the input clock rate. The chip adopts Explore’s proprietary eLVDS (Enhanced LVDS) technology which has the advantages of super high speed, low power consumption and wide operating voltage range (2.0V~2.75V) characteristics over the conventional LVDS technology. EP124 supports LVDS transmission for flat panel display up to 1080p double frame rate (120 Hz) by using only 2 ports of LVDS cable/connectors. This will simply system connectivity and save system cost. EP124 also supports interchip synchronization. By using 2 EP124 chips, 4port to 8port LVDS bridge can be achieved at a pixel rate of 660 MHz.

Serial digital video transmitter for HD video surveillance and HDcctv applications Dual rate operation 270Mbps and 1.485Gbps Backward compatible with HDcctv 1.0 and HDSDI (ST 292) Integrated High Definition Visually Lossless CODEC (HDVLC™) for extended cable reach 500m over 755 (5C) CCTV coax 300m over 753 (3C) CCTV coax 150m over Cat5e/6 UTP cable Configurable 50/75ohm cable driver output, for both coaxial and twisted pair cable transmission Integrated audio embedder with support for up to 4 channels of I2S serial digital audio at 32kHz, 44.1kHz and 48kHz sample rates Downstream ancillary data insertion Supports both 720p and 1080p HD formats 1080p 25/29.97/30fps 720p 25/29.97/30/50/59.94/60fps

BG96 est une série de LTE Cat.M1/Cat.NB1/EGPRS+ GNSS BG96 is a series of LTE Cat.M1/Cat.NB1/EGPRS module offering a maximum data rate of 375kbps downlink and uplink. It features ultra-low power consumption, and provides pin-to-pin compatibility with Quectel LTE module EG91/EG95, Cat.NB1 (NB-IoT) module BC95, UMTS/HSPA module UG95/UG96 and GSM/GPRS module M95. With a cost-effective SMT form factor of 22.5mm × 26.5mm × 2.3mm and high integration level, BG96 enables integrators and developers to easily design their applications and take advantage from the module’s low power consumption and mechanical intensity. Its advanced LGA package allows fully automated manufacturing for high-volume applications. Fast time-to-market:Reference designs, evaluation tools and timely technical support minimize design-in time

SG3225EEN Frenquency range:25 MHz to 200 MHz Supply voltage:2.5 V , 3.3 V Output:LV-PECL Function:Output enable (OE)

125 kHz, 134,2 kHz, 13,56 MHz, NFC et Bluetooth faible consommation 125 kHz, 134.2 kHz, 13.56 MHz, NFC and Bluetooth Low Energy. It can be connected through UART (TTL, RS232), USB, as well as Ethernet, and is available as a PCB and with Desktop housing. TWN4 MultiTech 2 BLE is also compatible with over 50 of the most common RFID technologies currently being used around the world. Furthermore, in order to expand the realm of supported contactless identification methods, the all-in-one reader also supports NFC and Bluetooth Low Energy. It is compatible with the two most commonly used smartphone operating systems - Android and iOS. Thus it can also be integrated in mobile identification applications. In addition, TWN4 MultiTech 2 BLE is flexibly programmable – when communicating with RFID transponders it can make automated decisions based on predefined rules. four frequencies:125/134.2 kHz, 13.56 MHz, 2.4 GHz

SC200R is Quectel’s new generation of multi-mode Smart LTE Cat 4 module with built-in Android OS. Based on Qualcomm Quad-core ARM Cortex-A53 64-bit Processors with built-in AdrenoTM 308 GPU. It is ideal for both industrial and consumer applications with high data-rate and multimedia functions. SC200R is available in five variants: SC200R-CE, SC200R-NA*, SC200R-EM*, SC200R-JP* and Wi-Fi & BT only version SC200R-WF*. SC200R supports multiple-input multiple-output (MIMO) technology. The use of multiple antennas at the receiver end at the same time and on the same frequency band greatly minimizes errors and optimizes the data speed. This module also combines high-speed wireless connectivity with embedded multi-constellation and high-sensitivity GNSS (GPS, Galileo, GLONASS and BeiDou) receiver for positioning. variants:SC200R-CE, SC200R-NA*, SC200R-EM*, SC200R-JP* and Wi-Fi & BT only version SC200R-WF*.

Double mode « LoRa-Sigfox » ou « LoRa seulement » DONGLE USB The MK002-xx-EU is the evaluation kit of the MM002-xx-EU module. Plugged onto a PC solution, this USB key allows to manage bi-directional communications through : LoRa™/FsK RF layers between USB key and any solution embedding MM002-xx-EU module LoRa™ WAN 1.0.2 EU Class A & C bidirectional protocol with Public or Private networks SIGFOX™ bidirectional protocol sent with 1/2 wave antenna Features: Modulation : LoRa™ / SIGFOX™/ FSK Controlled by AT commands through USB interface Good buildings penetration Long Range protocol stack software (SIGFOX™ / LoRa WAN 1.0 EU Class A & C) RoHS conform Pre-Certified EN 300-220 / RED directive WIKI PAGE => http://wiki.nemeus.fr/index.php?title=MM002_Evaluation_Kit_(MK002) Modulation:LoRa™ / SIGFOX™/ FSK

SG2016 CAN Frenquency range:1.2 MHz to 75 MHz Supply voltage:1.8 V ti 3.3 V typ. Function:Standby External dimensions:2.0 x 1.6 x 0.7 mm Output:CMOS

LTE Cat.1 module optimisé spécialement pour les applications M2M et IOTQuectel EG91 est une série de modules LTE de catégorie 1 optimisés spécialement pour les applications M2M et IoT. Il dispose d’une connectivité LTE rentable et basse consommation, et offre des vitesses optimisées M2M de 10Mbit/s downlink et 5Mbit/s uplink. Ceux-ci font d’EG91 une solution idéale pour de nombreuses applications IoT qui ne dépendent pas de la connectivité haute vitesse mais qui nécessitent toujours la longévité et la fiabilité des réseaux LTE. EG91 est compatible avec les modules Quectel UMTS/HSPA+ UG95/UG96 et Cat M1/Cat NB1 BG96. Cela le rend rétrocompatible avec les réseaux EDGE et GSM/GPRS existants, ce qui lui permet de migrer facilement des réseaux 2G/3G vers les réseaux 4G.

Sigfox RC1-RC6 global 'Monarch compatible', ble 4.2 module comboWS2116 est un module supportant à la fois Bluetooth Low Energy 4.2 et les transmissions Sigfox et ceci sur toutes les régions de RC1 à RC6 Ce module est basé sur le chip de ST Microelectronics S2-LP et le BlueNRG-2 SoC. Cette combinaison offre des performances RF optimales, de nombreuses E/S, 256KB de mémoire flash et permet le développement d'applications avec des durées d'utilisation sur batteries extrèmement longue. Ce module est actuellement échantillonné avec une production de volume planifiée pour le premier trimestre 2019.

EP952 is a Low Power HDMI (High Definition Multimedia Interface) transmitter. The chip is compliant with HDMI Rev 1.4 and HDCP Rev 1.4 specifications. The chip converts input video data in RGB or YUV format and audio data in IIS or SPDIF format into HDMI differential signals. The chip supports 8bit video upto 1080p in HDMI mode. The chip also supports 3D video. The chip supports highly flexible digital video input in a muxed 12bits mode or nonmuxed 24bit mode input. In both modes, the chip supports single or dual edge clocking HDMI Specification 1.4 Compliant Integrated HDCP encryption engine which is compliant with HDCP Rev 1.4 specification for transmitting protected content Integrated onchip HDCP Keys (Optional) Wide TMDS Clock Frequency Range

RX-4574 LC Interface type:3-wire serial interface Opening voltage range:1.6 V to 5.5 V Wide Timekeeper voltage range:1.3 V to 5.5 V Low backup current:0.35 µA / 3V (Typ.) 32.768 kHz frequency output function:C-MOS output With Conrtol Pin

Émetteurrécepteur RS232 de faible puissance 5V 250Kbps (Caractéristiques 28 broches, avec réveil, oscillation de tension de sortie ±6V) The ZT230E series devices are +5V powered EIA/TIA232 and V.28/V.24 communication interfaces with low power requirements. These transceivers consist of combinations up to five line drivers, five line receivers and the proprietary switchcapacitor regulated voltage converters. The ZT211E and ZT213E/AE feature a low power shutdown mode which draws as little current as 1µA typical with receiver outputs tristated and in wakeup. These devices operate from a single +5V power supply at the guaranteed data rate of 250K bits/sec with enhanced electrostatic discharge

The USB to MAC Ethernet Controller is a unique solution to interface 10/100 BaseT Ethernet devices to the Universal Serial Bus (USB2.0). This device has been specifically designed to provide a simple solution to communicate with Ethernet applications. This is accomplished by its highly integrated functionality. It is ideal for LAN (Local Area Network) applications. It provides internal buffering to enable parallel operations from USB ports on the host side, and MAC ports on the Ethernet side. It also provides a serial interface for an EEPROM for storing the MACID, VID, PID, and other configurable settings. USB 2.0 Device Controller Integrated USB 2.0 PHY USB Specification 2.0 Compliant Supports all USB Standard Commands Supports Five Vendor Specific Commands Supports USB Suspend/Resume Detection Logic 10/100 Mbps

Bluetooth Ver: Bluetooth 4.2 Transmission de la puissance: +8dB Sensibilité du récepteur: -85dB Antenne : BPC à bord Dimension: 7.0*7.0*1.0mm Certifications: FCC,RED, CE, IC, RoHs Bluetooth Ver:Bluetooth 4.2 Transmission de la puissance:+8dB Sensibilité du récepteur:'-85dB Antenne :BPC à bord Dimension:7.0*7.0*1.0mm Certifications:FCC,RED, CE, IC, RoHs Radio Feature Peak TX current:8.3ma Radio Feature RX peak current:7.7mA Sleep mode current:<700nA Operating temp:-40 ° C to 105 ° C Package size:7.0x 7.0x 1.0mm Operating voltage:1.8-3.6v

The AX88796B is a lowpincount (64pin LQFP) nonPCI Ethernet controller for the Embedded and Industrial Ethernet applications. The AX88796B supports 8/16bit SRAMlike host interface, providing a glueless connection to most common embedded MCUs. The AX88796B integrates onchip Fast Ethernet MAC and PHY, which is IEEE802.3 10BaseT and IEEE802.3u 100BaseTX compatible and 8Kx16 bits embedded SRAM for packet buffering to accommodate high bandwidth applications. The AX88796B has a wide array of features including support for Twisted Pair Crossover Detection and AutoCorrection, WakeonLAN power management and IEEE 802.3x and backpressure flow control. The AX88796B supports two operating temperature ranges, namely, commercial grade from 0 to 70 °C and industrial grade from 40 to 85 °C. The small form factor of 64pin LQFP package helps reduce the overall PCB space.

SG3225VEN Frenquency range:25 MHz to 200 MHz Supply voltage:2.5 V 3.3 V Output:LVDS Function:Output enable (OE)

Together with the EBGS2971 Evaluation Board, this document serves as a guide for evaluating the GS2971; a Gennum 3Gb/s, HD, SD SDI Receiver, with integrated equalizer. This document contains four main sections 1. Evaluation Board User Guide. 2. Evaluation Board Schematics. 3. Evaluation Board Layout. 4. Evaluation Board Bill of Materials The figure below shows a block diagram of the features and the functions of the EBGS2971. The board includes a power supply, a 3GSDI input, a 3GSDI loopthrough output, a GS2971 Receiver, a parallel video output connector, an audio output with four BNCs for AES audio, a fourpin header for serial audio, a JTAG/GSPI header, a 27MHz crystal, a DIP switch and some status indication LEDs. The GS2971 will automatically detect the input signal as SDSDI, HDSDI or 3GSDI. The

EP105 is a high speed 10bit LVDS (Low Voltage Differential Signal) transmitter capable of transmitting LVDS outputs at 150 Mhz clock rate. The chip adopts Explore’s proprietary eLVDS (Enhanced LVDS) technology which was developed for supper high speed LVDS interface. EP105 along with EP106 (eLVDS receiver) support single link transmission between the host and the flat panel display up to 1080p resolution. The chip converts 32 bits (10bits/color, 2 dummy bits) of CMOS/TTL data and 3 control bits into 5 LVDS data streams. At the maximum input clock rate of 150MHz, each LVDS differential data pair speed is 1.05 Gbps, providing a total throughput of 5.25 Gbps. The transmitter can be configured to input clock rising edge or falling edge strobe through an external pin. Support 8MHz to 150MHz clock rates from NTSC to 1080p resolution Up to 5.25Gbps bandwidth

MCS9901CVCC is a single lane multifunction PCI express to I/O controller. It supports two serial ports, one parallel port and six GPIO's. MCS9901CVCC also provides an option for peripheral expansion through proprietary Cascade interface. The generic cascade interface allows interconnecting with similar chips like MCS9900, MCS9950 to expand the peripheral ports. The serial ports are compatible with RS232, RS422 & RS485 standards and supports throughput from 50bps to 16Mbps. Parallel Port is compatible with IEEE 1284 and supports Nibble, Byte, SPP, ECP, and EPP modes. All the GPIO pins are programmable and can be used as Input or Output. An I²C interface is provided to configure MCS9901CVCC device options through an external EEPROM. PCI Express Singlelane (X1) PCI Express Endpoint Controller with integrated PHY Compliant with PCI Express Base Specification, Revision 1.1

Émetteursrécepteurs RS232 de faible puissance 5V 250Kbps (Caractéristiques 28 broches, w/o Wake Up, ±6V Output Voltage Swing) The ZT230E series devices are +5V powered EIA/TIA232 and V.28/V.24 communication interfaces with low power requirements. These transceivers consist of combinations up to five line drivers, five line receivers and the proprietary switchcapacitor regulated voltage converters. The ZT211E and ZT213E/AE feature a low power shutdown mode which draws as little current as 1µA typical with receiver outputs tristated and in wakeup. These devices operate from a single +5V power supply at the guaranteed data rate of 250K bits/sec with enhanced electrostatic discharge (ESD) protection in all RS232 I/O pins exceeding ±15kV HBM.

Multi-mode LTE Cat.M1/Cat.NB2/EGPRS+ GNSS Size: 19.9 x 23.6 x 2.3mm LGA package BG95 is a series of LTE Cat.M1/Cat.NB5/EGPRS module with integrated GNSS. It is fully compliant with 3GPP Rel. 14 specification and offers a maximum data rate of 375Kbps downlink and 1.2Mbps uplink. It features ultra- low power consumption by leveraging the integrated RAM/flash as well as the ARM Cortex A7 processor supporting ThreadX, achieving up to 70% reduction in PSM leakage and 85% reduction in eDRX current consumption compared to its predecessor. BG95 boasts a comprehensive set of hardware-based security features and enables trusted applications to run directly on the Cortex A7 TrustZone engine. As well, BG95 provides pin-to-pin compatibility with Quectel LTE module EG91/EG95, LPWA module BG96 & BC95, UMTS/HSPA module UG95/UG96 and GSM/GPRS module M95. Fast time-to-market:Reference designs, evaluation tools and timely technical support minimize design-in time

The MCS7832 USB to 10/100 Ethernet Controller is a unique solution to interface 10/100 BaseT Ethernet devices to the Universal Serial Bus (USB2.0). This device has been specifically designed to provide a simple, low cost solution to communicate with applications needing plugand play 10/100 Ethernet connectivity with minimal design time. This is accomplished by its highly integrated functionality, robust software suite, WHQL and USBIF certification, low pincount and high performance. It provides internal buffering to enable parallel operations from USB ports on the host side, and MAC ports on the Ethernet side. It also provides a serial interface for an EEPROM for storing the MACID, VID, PID, and other configurable settings. USB 2.0 Device Controller Supports HS (480Mbps) and FS (12Mbps) modes USB

Cliquer sur l'image afin de mieux voir

Quectel EG06 est une série de modules LTE Cat.6 optimisés spécialement pour les applications M2M et IoT Quectel EG06 est une série de modules LTE Advanced de catégorie 6 optimisés spécialement pour les applications M2M et IoT. Adoptant la technologie 3GPP Rel. 12 LTE, il offre des vitesses optimisées m2M de 300 Mbit/s downlink et 50Mbit/s uplink taux de données de pointe. Conçu dans le facteur de forme LGA, EG06 est compatible avec le futur module Cat.9 DE Quectel EG09, le module Cat.12 EG12 et le module Cat.16 EG16 , qui aidera les clients à migrer entre différentes catégories à l’avenir. EG06 contient 5 variantes (EG06-E, EG06-A, EG06-LA, EG06-APAC et EG06-AUTL) qui sont conçues pour différentes régions cibles et couvrent presque tous les principaux transporteurs de cours d’eau dans le monde entier. EG06 prend en charge la technologie de localisation Gen8C Lite de Qualcomm™® IZat (GPS, GLONASS, BeiDou, Galileo et QZSS). Améliorations des fonctionnalités:prend en charge DFOTA*, eCall* et DTMF

Cliquer sur l'image afin de mieux voir

Module sans fil ultra-compact et fiable SIM8905 basé sur la plate-forme LTE multi-mode Qualcomm MSM8909. GSM/GPRS/EDGE/EGSM:850/900/DCS1800 Supply voltage range:3.4 ~ 4.4 V Operation temperature:-25℃to +75℃ Dimension:40.5*40.5*2.8mm Weight:10.6g WCDMA/HSPA/HSPA+:42.2 Mbps(DL),11.5